Comparative Analysis of the Results of the Determination of Allowances According to Standards and the Calculation and Analytical Method Using the Dimensional Analysis of Technological Processes
DOI:
https://doi.org/10.31649/1997-9266-2022-165-6-69-74Keywords:
mechanical processing, determination of allowances, normative method, calculation and analytical method, dimensional analysis of technological processesAbstract
A comparative analysis of the results of determining the general allowance according to the standards and the allowance determined using the calculation-analytical method on the example of processing by boring the main hole in the workpiece of the body part was performed. The studies were carried out on the example of the technological process of mechanical processing of the workpiece of the "Hull" type part. The determination of technological dimensions and dimensions of the initial workpiece, as well as intermediate allowances and general allowance for all transitions of processing (boring) of one of the main holes is considered. It was believed that the initial workpiece is casting in shell molds. To determine one of the components of the minimum pass, namely the spatial deviations of the surface of the hole relative to technological bases, the dimensional analysis apparatus of the technological process was used, which takes into account the specific conditions of this process, in particular, the peculiarities of the scheme of basing on the first operation.
A comparison of the amount of the total minimum allowance determined using the calculation-analytical method with the amount of the total allowance determined according to the normative tables showed that the calculated allowance exceeds the standard by almost 30%, and the most significant influence on the amount of the calculated total allowance is the value of the spatial deviation of the axis of the hole in the initial workpiece relative to the technological bases. Therefore, if the first operation of the technological process solves the problem of ensuring the dimensional relationship between the processed and untreated surfaces, then the allowance determined according to the standards during the processing of a batch of blanks on a set machine may not be enough to ensure the required surface quality details Therefore, in this case, it is necessary to use the calculation and analytical method to determine both the intermediate allowances and the total allowance.
References
В. М. Кован, и др., Корсаков В. С., Ред., Основы технологии машиностроения, М.: Машиностроение, 1977, 416 с.
В. Б. Борисов, и др., А. Г. Косилова, Р. К. Мещеряков, Ред., Справочник технолога-машиностроителя, в 2 т, т. 1. М.: Машиностроение, 1985, 656 с.
О. В. Дерібо, Основи технології машинобудування. Частина 2, навч. посіб. Вінниця: ВНТУ, 2015, 116 с.
О. В. Дерібо, Ж. П. Дусанюк, і С. І. Сухоруков, Основи технології машинобудування. Частина 2, практикум. Вінниця: ВНТУ, 2015, 116 с.
В. В. Бабук, и др., В. В. Бабук, Ред. Проектирование технологических процессов механической обработки в машиностроении, Минск: Вышэйшая школа, 1987, 255 с.
О. В. Дерібо, Ж. П. Дусанюк, С. В. Репінський, і Д. А. Боровський, «Вплив схеми базування на першій операції на величину припуску для розточування отворів в корпусних деталях на настроєних верстатах,» Вісник Вінницького політехнічного інституту, № 6, с. 95-103, 2018.
О. В. Дерібо, Ж. П. Дусанюк, і Т. М. Горук, «Застосування розмірного аналізу у визначенні мінімального проміжного припуску на механічну обробку отворів у корпусних деталях,» Вісник Вінницького політехнічного інституту, № 4, с. 77-80, 2009.
В. Д. Рудь, О. О. Герасимчук, і Т. П. Маркова, Розмірно-точнісний аналіз конструкцій та технологій. Луцьк: ЛДТУ, 2008, 344 с.
В. Д. Мягков, М. А. Палей, А. Б. Романов, и В. А. Брагинский, Допуски и посадки, справ. в 2-х ч. Л.: Машиностроение, ч. 2, 1983, 448 с.
«Отливки из металлов и сплавов. Допуски размеров, массы и припуски на механическую обработку,» ГОСТ 26645-85. Введ. 1987.07.01. М.: Изд-во стандартов, 1987, 53 с.
Downloads
-
PDF (Українська)
Downloads: 100
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
